TJ General Store
Elzetta Tactical Flashlight Mount
Finally, an inexpensive tactical flashlight mount for the M-16/AR-15 that adjusts for flashlight barrel diameters of .7 to 1.1 inches. This mount can accommodate tailcap pushbutton and barrel rotating switches as well as pressure pad momentary switches. Available in three colors, Black, OD Green, and the new Dark Earth. Made in the USA from glass-filled polymer. Mounts in seconds using the screws and tool included. Included sizing adapter provides a firm grip on even the smallest .7 inch tactical light. Mounts on barrels with or without a bayonet lugs. The mount holds the flashlight firmly in place even during automatic or rapid fire tactical situations. If your light can take the pounding and the heat, so can the mount. Mounted accessories do not interfere with ACOG type sights or tactical lasers mounted on the receiver. Add a Tactical Rail Kit and you can mount another accessory on the left or right of the sight. See our Frequently Asked Questions section below for more information on this great mount.
Elzetta Design, LLC
P.O. Box 54364
Lexington, KY 40555
(859) 707-7471
(Flashlight not included)
Shown with optional Tactical Rail Kit (Flashlight not included)
Shown with optional Tactical Rail Kit (Flashlight not included)
Black
OD
Dark Earth
Tactical Rail Kit (fits Weaver or Picatinny) (Flashlight not included)
| Order Number | Description | Price | |
|
ZFH1500B |
Elzetta Flashlight Mount, Black (Flashlight not included) |
29.95 |
|
| ZFH1500T | Elzetta Flashlight Mount, Dark Earth (Flashlight not included) | 29.95 | |
| ZFH1500G | Elzetta Flashlight Mount, Olive Drab (Flashlight not included) | 29.95 | |
| ZPR1500B | Elzetta Tactical Rail Kit, one rail, screws and tool, Black (Flashlight not included) Fits above mounts only | 6.95 |
|
The Elzetta ZORM
|
|
|
The new ZORM Tactical Flashlight Holder features all metal construction with a main body of Mil-Spec Type III Hard Anodized 6061-T6 Aluminum. The ZORM attaches to Mil-Std 1913 Picatinny Rails in an ergonomic low profile offset position. Elzetta's signature spacer system is included enabling the ZORM to accommodate all flashlights ranging from 0.7 to 1.1" in diameter. The ZORM is secured with a coin-tightened Thumb Nut that may be locked in place with either a safety wire or included cotter pin. A Picatinny Rail can be purchased below to add additional accessories.(ZPR118) All Elzetta products are Made in the USA.
|
|
The Elzetta ZROC
|
|
The new Elzetta ZROC Tactical Flashlight Holder features all metal construction with a main body of Mil-Spec Type III Hard Anodized 6061-T6 Aluminum. The ZROC attaches to Mil-Std 1913 Picatinny Rails in an ergonomic low profile offset position using dual coin-tightened Thumb Nuts for extra holding power. The Thumb Nuts may be secured using either a safety wire or the included cotter pins. ZROC also features a Quick-Release Thumb Screw for rapid installation and removal of flashlights and an integrated Picatinny Rail for attaching a laser, navigation light, or other accessory. An additional Picatinny Rail can be purchased below to add additional accessories.(ZPR118) |
|
ZPR118
Mil-Spec Type III Hard Anodized Aluminum Picatinny Rail fits ZORM and ZROC Allows the addition of an additional Picatinny Rail to the ZROC or ZORM for attachment of an additional accessory. |
| Order Number | Description | Price | |
|
ZORM |
Elzetta ZORM Mount, black |
59.95 |
|
| ZROC |
Elzetta ZROC Mount, black |
69.95 | |
| ZPR118 |
Elzetta Picatinny Rail for ZROC and ZORM, black |
13.95 |
ZROC and ZORM Spare Parts
Thumb Screw Kit ($7.95) |
Screw Kit ($0.95) |
Sizing Adaptors ($3.95) |
| Order Number | Description | Price | |
|
TS-Kit |
Elzetta Spare Parts Thumb Screw Kit for ZROC |
7.95 |
|
| S-Kit |
Elzetta Spare Parts Screw Kit for ZROC and ZORM |
.95 | |
| Sizers |
Elzetta Spare Parts Sizing Adapter for ZORM and ZORM |
3.95 |
|
Frequently Asked Questions: What flashlights will work with the Elzetta ZFH1500? Each Elzetta ZFH1500 comes with Sizing Adapters, giving the Flashlight Holder the ability to mount flashlights from 0.7 to 1.1 inches in diameter (18 to 28 mm). This includes such popular flashlights as the Mini-MagLite® and many SureFire® models. (Flashlight not included) Will the Elzetta ZFH1500 fit rifles equipped with a bayonet lug? Yes, the ZFH1500 is designed to fit around the standard bayonet lug. In fact, the bayonet lug adds strength to the flashlight holder assembly. Will the Elzetta ZFH1500 hold a Laser? Yes, the Elzetta ZFH1500 can be used to mount any cylindrical accessory with an outer diameter of 0.7 to 1.1 inches (18 to 28 mm). What material is the ZFH1500 Flashlight Holder made from? The Elzetta ZFH1500 is made from a glass-filled polymer. What are the advantages of this material? This glass-filled polymer provides outstanding durability, impact resistance, scratch resistant, and light weight. It also withstands high temperatures, vibration, and most chemicals. How much does the Elzetta ZFH1500 weigh? The Flashlight Holder with hardware weighs only 2.8 oz (79 g). Will attaching a sling on the front sling swivel interfere with the use of the ZFH1500? No, Elzetta designed the ZFH1500 to work in various configurations. When the flashlight is mounted rearward (with the tailcap exposed), the sling swivel (with or without a sling attached) will activate the push-button switch of the flashlight. When the flashlight is mounted with the tailcap recessed into the ZFH1500 body, the push-button switch is protected from the sling swivel while the tailcap of the flashlight is still accessible through the skeleton hole in the ZFH1500 body. Will the Elzetta ZFH1500 work with a heavy barrel (HBAR)? Yes, the ZFH1500 was designed around the standard HBAR and will work with any barrel that has a diameter of 0.75 inch (19mm) or less at the front sight. Will the Elzetta Mount hold a laser sight? Yes, it will hold any round device .7 to 1.1 inches in diameter. Please be sure you can reach the switch and windage and elevation adjustments on the laser you are going to use. Will my AR15 fit in its storage case when fitted with an Elzetta ZFH1500 Flashlight Holder? Yes, the ZFH1500's center line mounting position preserves the slim profile of the AR15 rifle, allowing storage in most gun cases. Will the Elzetta ZFH1500 fit an Airsoft Rifle? Yes, the ZFH1500 will fit many Airsoft AR15/M4 replica rifles. Some may require minor modification. Where is the Elzetta ZFH1500 made? Every ZFH1500 Flashlight Holder is designed, engineered, and Made in the USA using American tooling and American made thermoplastic resins. |
|
Frequently Asked Questions: When will the new Elzetta ZORM be available? The Elzetta ZORM should be available around Thanksgiving 2008. What flashlights will work with Elzetta ZORM? Every Elzetta ZORM comes with Sizing Adapters, giving the Flashlight Holder the ability to mount flashlights from 0.7 to 1.1 inches in diameter (18 to 27 mm). This includes such popular flashlights as the Mini-MagLite®, PentagonLight®, Inova®, Streamlight®, Pelican®, Laser Devices®, and many SureFire® models. What materials is the Elzetta ZORM Flashlight Holder made from? The Elzetta ZORM features all metal construction with a main body of Mil-Spec Type III Hard Anodized 6061-T6 Aluminum, a matte black stainless steel flashlight clamp, and matte black steel hardware. Can the Elzetta ZORM be permanently locked to a rail? Yes, the castle- style Thumb Nut may be secured with safety wire or the included cotter pin. Why are there two tapped holes in the Elzetta ZORM? The two tapped holes accommodate the attachment of an Elzetta ZPR118 Picatinny Rail, which allows the mounting of an additional accessory. ZPR118 sold separately. How much does the Elzetta ZORM weigh? The Flashlight Holder with hardware weighs 2.4oz (68g). Where is the Elzetta ZORM made? All Elzetta products, including the ZORM, are designed, engineered, and manufactured in the USA using American tooling and American made materials.
|
|
Frequently Asked Questions: When will the new Elzetta ZROC be available? The Elzetta ZROC should be available around Thanksgiving 2008. What flashlights will work with Elzetta ZROC? Every Elzetta ZROC comes with Sizing Adapters, giving the Flashlight Holder the ability to mount flashlights from 0.7 to 1.1 inches in diameter (18 to 27 mm). This includes such popular flashlights as the Mini-MagLite®, PentagonLight®, Inova®, Streamlight®, Pelican®, Laser Devices®, and many SureFire® models. What advantage does the Quick-Release Thumb Screw offer? The Quick-Release Thumb Screw allows flashlights to be installed and removed rapidly and without tools. Why does the Elzetta ZROC have an integrated Picatinny Rail? The integrated Picatinny Rail allows the mounting of an additional accessory such as a laser or navigational light. Why does the Elzetta ZROC have dual Thumb Nuts? The dual Thumb Nuts enhance the strength and rigidity of the device. This is an important feature when attaching an accessory to the integrated Picatinny Rail. What materials is the Elzetta ZROC Flashlight Holder made from? The Elzetta ZROC features all metal construction with a main body of Mil-Spec Type III Hard Anodized 6061-T6 Aluminum, a matte black stainless steel flashlight clamp, and matte black steel hardware. Can the Elzetta ZROC be permanently locked to a rail? Yes, the castle- style Thumb Nuts may be secured with safety wire or the included cotter pins. Why are there two tapped holes in the Elzetta ZROC? The two tapped holes accommodate the attachment of an Elzetta ZPR118 Picatinny Rail, which allows the mounting of an additional accessory. ZPR118 sold separately. How much does the Elzetta ZROC weigh? The Flashlight Holder with hardware weighs 3.0oz (85g). Where is the Elzetta ZROC made? All Elzetta products, including the ZROC, are designed, engineered, and manufactured in the USA using American tooling and American made materials.
|
Text and images courtesy of Elzetta
